Publicacións en colaboración con investigadores/as de Universidade de Aveiro (21)

2020

  1. Autonomous Robots and CoBots: Applications in Manufacturing

    Enabling Technologies for the Successful Deployment of Industry 4.0 (CRC Press), pp. 47-66

2019

  1. Enhancing Productivity by Means of High Feed Rate in the Drilling of Al 2011 Aluminium Alloy

    Arabian Journal for Science and Engineering, Vol. 44, Núm. 9, pp. 8035-8042

  2. Facing the challenges of the food industry: Might additive manufacturing be the answer?

    Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 233, Núm. 8, pp. 1902-1906

  3. Investigation of surface integrity induced on AZ31C magnesium alloy turned under cryogenic and dry conditions

    Procedia Manufacturing

  4. Machining of a biomaterial with dual negative tool geometry

    Mechanical Behaviour of Biomaterials (Elsevier), pp. 117-128

2018

  1. A novel method for the determination of fatty acid esters in aqueous emulsion on Ti6Al4V surface with IRRAS and carbon quantification

    Tribology International, Vol. 128, pp. 155-160

  2. Surface quality enhancement of fused deposition modeling (FDM) printed samples based on the selection of critical printing parameters

    Materials, Vol. 11, Núm. 8

2017

  1. Latest advances in the micro-milling of titanium alloys: a review

    Procedia Manufacturing, Vol. 13, pp. 275-282

  2. Study Based on Sound Monitoring as a Means for Superficial Quality Control in Intermittent Turning of Magnesium Workpieces

    Procedia CIRP

  3. Technical, Economic and Environmental Review of the Lubrication/Cooling Systems Used in Machining Processes

    Procedia Engineering

2016

  1. Analysis of the hard turning of AISI H13 steel with ceramic tools based on tool geometry: surface roughness, tool wear and their relation

    Journal of the Brazilian Society of Mechanical Sciences and Engineering, Vol. 38, Núm. 8, pp. 2413-2420

  2. Comparative study of the performance of diamond-coated drills on the delamination in drilling of carbon fiber reinforced plastics: Assessing the influence of the temperature of the drill

    Journal of Composite Materials, Vol. 50, Núm. 2, pp. 179-189

  3. Delamination of carbon fiber reinforced plastics: Analysis of the drilling method

    Indian Journal of Engineering and Materials Sciences, Vol. 23, Núm. 2-3, pp. 134-138

  4. Surface Roughness Investigation in the Hard Turning of Steel Using Ceramic Tools

    Materials and Manufacturing Processes, Vol. 31, Núm. 5, pp. 648-652

  5. The effect of minimum quantity lubrication in the intermittent turning of magnesium based on vibration signals

    Measurement: Journal of the International Measurement Confederation, Vol. 94, pp. 338-343

2015

  1. A note on the use of the minimum quantity lubrication (MQL) system in turning

    Industrial Lubrication and Tribology, Vol. 67, Núm. 3, pp. 256-261

  2. Analysis of ignition risk in intermittent turning of UNS M11917 magnesium alloy at low cutting speeds based on the chip morphology

    Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 229, Núm. 2, pp. 365-371

  3. Specific cutting energy employed to study the influence of the grain size in the micro-milling of the hardened AISI H13 steel

    International Journal of Advanced Manufacturing Technology, Vol. 81, Núm. 9-12, pp. 1591-1599

2014

  1. Discontinuous cutting: Failure mechanisms, tool materials and temperature study - A review

    Reviews on Advanced Materials Science, Vol. 38, Núm. 2, pp. 110-124

  2. Experimental investigation on finish intermittent turning of UNS M11917 magnesium alloy under dry machining

    International Journal of Advanced Manufacturing Technology, Vol. 75, Núm. 9-12, pp. 1417-1429